블로그로 돌아가기
사용 방법 가이드 2026-11-15 clast.com.au 1 조회수

Vanguard Endeavor RS IV 4-16X50 Dispatch 800: Zeroing Guide

Vanguard Endeavor RS IV 4-16X50 Dispatch 800: Zeroing Guide

A practical zeroing sequence for the Vanguard Endeavor RS IV 4-16X50 Dispatch 800, using only the turret, reticle and mounting facts confirmed in the catalog.

What the catalog confirms before you start

The Endeavor RS IV 4-16X50 Dispatch 800 is a 30mm-tube riflescope with an illuminated Dispatch ballistic reticle, a four-times zoom range and a rapid focus eyepiece. Its windage and elevation turrets adjust in 1/4 M.O.A clicks and include a zero reset feature. The catalog also lists a 30mm tube diameter, a one-piece T6061 aluminum body and MultiGuard coatings.

Those facts give you a zeroing plan: mount the scope in 30mm rings, confirm the reticle is level, bore-sight if your range allows, fire a group, then move the point of impact with 1/4 M.O.A clicks. The catalog does not supply a specific torque value, ring height, or a step-by-step factory zeroing procedure, so follow your ring and rifle manufacturer's instructions for mounting hardware.

Turret and reticle facts that drive the zero

A supported zeroing sequence

Work through these steps in order. Stop and re-check if anything feels loose or inconsistent.

  1. Mount in 30mm rings: Use rings sized for the catalog's 30mm tube. Set the scope so the eye relief suits your cheek weld, then tighten the ring caps evenly in a cross pattern. The catalog does not list a torque specification, so use the ring manufacturer's value.
  2. Level the reticle: With the rifle held level, align the vertical reticle post with a plumb line or a leveled target. A canted reticle will make windage and elevation adjustments track diagonally.
  3. Bore-sight at short range: If your range or a bore-sighting tool allows, align the bore and the scope's primary aiming point on the same target at a short distance. This gets you on paper before live fire.
  4. Fire a three-shot group: Aim at the same point for each shot. Let the barrel cool between groups if it heats quickly. Mark the center of the group as your point of impact.
  5. Adjust with 1/4 M.O.A clicks: Measure how far the group center is from your aim point, then convert that distance to clicks using the catalog's 1/4 M.O.A / 7mm at 100m figure. Move elevation first, then windage, and fire another group to confirm.
  6. Reset the turrets to zero: Once the group centers on your aim point, use the zero reset feature to set the turret markings to zero. Confirm the setting by firing a final group.

Using the Dispatch reticle after zero

The Dispatch 800 reticle is a ballistic design, which means the lower marks are intended as holdover references. The catalog does not list the exact distance each mark corresponds to, so you will need to verify them on the range with your own load. Set targets at known distances, aim with the appropriate holdover mark, and record where each group lands.

Because the reticle is illuminated, check that the illumination works before you rely on it in low light. The catalog lists a CR 2032 battery type for the illuminated models, so keep a spare on hand. The catalog does not confirm battery life, so test the illumination before a hunt rather than assuming it will last a full season.

Optical and body facts worth knowing at the range

Mounting tips specific to this scope

The one-piece 30mm tube gives you a continuous mounting surface, but ring placement still matters. Keep the front ring off the objective bell and the rear ring clear of the eyepiece and turret housing. The catalog lists an objective diameter of 42, so check that your chosen ring height clears the barrel and any rail.

The catalog does not confirm a specific ring height, torque value, or eye relief distance for this model. Set eye relief by shoulder the rifle with your eyes closed, then open them and check for a full, shadow-free view. Adjust the scope forward or back in the rings before final tightening.

관련 게시글

Customer Service
홈
상품
장바구니
내 정보