What the catalog confirms before you start
The Endeavor RS IV 4-16X50 Dispatch 800 is a 30mm-tube riflescope with an illuminated Dispatch ballistic reticle, a four-times zoom range and a rapid focus eyepiece. Its windage and elevation turrets adjust in 1/4 M.O.A clicks and include a zero reset feature. The catalog also lists a 30mm tube diameter, a one-piece T6061 aluminum body and MultiGuard coatings.
Those facts give you a zeroing plan: mount the scope in 30mm rings, confirm the reticle is level, bore-sight if your range allows, fire a group, then move the point of impact with 1/4 M.O.A clicks. The catalog does not supply a specific torque value, ring height, or a step-by-step factory zeroing procedure, so follow your ring and rifle manufacturer's instructions for mounting hardware.
Turret and reticle facts that drive the zero
- Vanguard Endeavor RS IV 4-16X50 Dispatch 800 Riflescope: Adjustment per click: 1/4 M.O.A / 7mm at 100m This is the unit you will use to move the point of impact. At 100 meters, one click moves impact by roughly 7mm; four clicks move it about one M.O.A.

Vanguard Endeavor RS IV 4-16X50 Dispatch 800 Riflescope - Vanguard Endeavor RS IV 4-16X50 Dispatch 800 Riflescope: Precise windage and elevation adjustment with zero reset feature After you have a confirmed zero, the reset feature lets you return the turret markings to zero without changing the actual adjustment.
- Vanguard Endeavor RS IV 4-16X50 Dispatch 800 Riflescope: Illuminated Dispatch ballistic reticle The Dispatch reticle is designed for holdover reference, so zero the scope at the distance your reticle's primary aiming point is intended for, then verify the holdover marks at the range.
- Vanguard Endeavor RS IV 4-16X50 Dispatch 800 Riflescope: 30 / 1.18 tube diameter (mm/in) You need 30mm rings. Confirm the ring height clears your rifle's objective and eyepiece before tightening anything.
A supported zeroing sequence
Work through these steps in order. Stop and re-check if anything feels loose or inconsistent.
- Mount in 30mm rings: Use rings sized for the catalog's 30mm tube. Set the scope so the eye relief suits your cheek weld, then tighten the ring caps evenly in a cross pattern. The catalog does not list a torque specification, so use the ring manufacturer's value.
- Level the reticle: With the rifle held level, align the vertical reticle post with a plumb line or a leveled target. A canted reticle will make windage and elevation adjustments track diagonally.
- Bore-sight at short range: If your range or a bore-sighting tool allows, align the bore and the scope's primary aiming point on the same target at a short distance. This gets you on paper before live fire.
- Fire a three-shot group: Aim at the same point for each shot. Let the barrel cool between groups if it heats quickly. Mark the center of the group as your point of impact.
- Adjust with 1/4 M.O.A clicks: Measure how far the group center is from your aim point, then convert that distance to clicks using the catalog's 1/4 M.O.A / 7mm at 100m figure. Move elevation first, then windage, and fire another group to confirm.
- Reset the turrets to zero: Once the group centers on your aim point, use the zero reset feature to set the turret markings to zero. Confirm the setting by firing a final group.
Using the Dispatch reticle after zero
The Dispatch 800 reticle is a ballistic design, which means the lower marks are intended as holdover references. The catalog does not list the exact distance each mark corresponds to, so you will need to verify them on the range with your own load. Set targets at known distances, aim with the appropriate holdover mark, and record where each group lands.
Because the reticle is illuminated, check that the illumination works before you rely on it in low light. The catalog lists a CR 2032 battery type for the illuminated models, so keep a spare on hand. The catalog does not confirm battery life, so test the illumination before a hunt rather than assuming it will last a full season.
Optical and body facts worth knowing at the range
- Vanguard Endeavor RS IV 4-16X50 Dispatch 800 Riflescope: Premium Hoya ED Glass provides true color and edge to edge clarity Clear glass helps you see the target and the reticle marks distinctly when you are confirming holdovers at distance.
- Vanguard Endeavor RS IV 4-16X50 Dispatch 800 Riflescope: Advanced MultiGuard coatings for higher light transmittance Better light transmission helps in early and late light, but it does not replace correct eye placement or a stable rest.
- Vanguard Endeavor RS IV 4-16X50 Dispatch 800 Riflescope: Rapid focus eyepiece Focus the eyepiece on the reticle before zeroing so your eye does not drift between the reticle and the target.
- Vanguard Endeavor RS IV 4-16X50 Dispatch 800 Riflescope: Sealed against dust and moisture, nitrogen purged, and recoil resistant These are useful field qualities, but they do not confirm a specific waterproof rating or a maximum recoil tolerance. Treat them as general durability claims from the catalog.
Mounting tips specific to this scope
The one-piece 30mm tube gives you a continuous mounting surface, but ring placement still matters. Keep the front ring off the objective bell and the rear ring clear of the eyepiece and turret housing. The catalog lists an objective diameter of 42, so check that your chosen ring height clears the barrel and any rail.
The catalog does not confirm a specific ring height, torque value, or eye relief distance for this model. Set eye relief by shoulder the rifle with your eyes closed, then open them and check for a full, shadow-free view. Adjust the scope forward or back in the rings before final tightening.

