Back to Blog
How-to Guides 2026-11-17 clast.com.au 1 views

Vanguard Endeavor RS IV 5-20X50: Varmint Scope Setup Guide

Vanguard Endeavor RS IV 5-20X50: Varmint Scope Setup Guide

Set up the Vanguard Endeavor RS IV 5-20X50 for varmint hunting: mounting, eye relief, turret zeroing, and using the Dispatch reticle at its Optimized Power Setting.

Why this scope suits varmint work

The Vanguard Endeavor RS IV 5-20X50 Dispatch Varmit Riflecsope 52050DSV is built around a 5-20x magnification range and a 50mm objective, with an illuminated Dispatch Varmint reticle. Vanguard describes the platform as suitable for target shooting, varmint and predator hunting, and for sizing up antler detail. The Dispatch Varmint reticle is specifically designed for high-velocity, lower-bullet-weight calibers such as .22-250 REM, .220 Swift, and .204 Ruger, with a 200-yard zero providing a smooth transition from zero to 600 yards.

Setup matters more than the spec sheet here because the reticle's holdover function only works at a specific magnification. Vanguard states that all Endeavor riflescopes with the second image plane Dispatch reticle must be set to the Optimized Power Setting (OPS) to use holdover successfully. The Dispatch ballistic calculator generates and displays that OPS along with actual bullet drop at each distance, using inputs like caliber, bullet weight, velocity, ballistic coefficient, elevation, temperature, and humidity.

Catalog facts that shape your setup

Mounting and eye relief: getting the scope on the rifle

The catalog gives eye relief as 4.13 - 3.54 in. Use those figures to position the scope in the rings so you have a consistent, comfortable cheek weld across the magnification range. Because eye relief changes with magnification, check your position at both 5x and 20x before final tightening. The 30mm tube requires 30mm rings; confirm ring height clears the 50mm objective without contact.

  1. Check ring and base compatibility: The scope has a 30mm aircraft-grade aluminum body. Use 30mm rings and a base suited to your rifle's receiver.
  2. Set preliminary eye relief: With the scope loosely in the rings, shoulder the rifle and adjust fore/aft position until the view is full at both 5x and 20x, staying within the 4.13 - 3.54 in eye relief range.
  3. Level the reticle: Use a plumb line or leveling kit to align the reticle with the rifle's vertical axis before torquing ring screws to the ring manufacturer's specification.
  4. Confirm clearance: Verify the 50mm objective and the fast focus eyepiece clear the barrel and bolt handle through the full magnification range.

Zeroing the Endeavor RS IV 5-20X50

The scope has precise windage and elevation adjustment with a zero reset function and 1/4 M.O.A / 7MM at 100M click value. Start at a short distance you can reliably group at, then move to your intended zero distance. Vanguard's Dispatch Varmint reticle is designed around a 200-yard zero, so that is the logical final zero for this scope if you plan to use the holdover function.

  1. Bore-sight or start close: Get on paper at a short distance before shooting at your zero distance. This saves ammunition and confirms the mount is secure.
  2. Adjust in confirmed click values: Each click is 1/4 M.O.A / 7MM at 100M. Make corrections in whole clicks and re-fire to confirm.
  3. Set the zero stop with the zero reset function: Once you have a confirmed zero, use the zero reset function to align the turret markings with your zero position.
  4. Confirm at distance: Fire a group at your intended zero distance (200 yards for the Dispatch Varmint design) to verify point of impact before relying on holdover.

Using the Dispatch Varmint reticle at the Optimized Power Setting

The Dispatch Varmint reticle is an etched, illuminated design with reticle subtensions of .125 inches for fine shot placement on small targets. It is a second image plane reticle, which is why the OPS matters: holdover values are only correct at the magnification Vanguard's Dispatch ballistic calculator specifies for your load. Before you hunt, enter your caliber, bullet weight, velocity, ballistic coefficient, elevation, temperature, and humidity into the calculator, note the OPS and the displayed drop at each distance, then set the scope to that magnification and leave it there when using holdover.

The reticle is designed around high-velocity, lower-bullet-weight calibers and a 200-yard zero. If you shoot a different cartridge or zero distance, the holdover values will not match the reticle's design intent; the calculator's output is your reference, not a generic chart.

Magnification, illumination, and low-light use

  • Magnification for varmints: The 5-20x range covers close encounters through longer shots. Use lower magnification for wide field of view and higher magnification for small targets at distance, but return to the OPS when using holdover.
  • Illumination: The illuminated reticle runs on a CR 2032 battery (included). Vanguard states the 50mm objective and illuminated reticle system eliminate shooter sacrifice in low light.
  • Optical coatings: Premium HOYA ED optics and Advanced MultiGuard® coatings are specified for true-to-life colors, edge-to-edge clarity, and increased light transmittance.
  • Focus: The fast focus eyepiece lets you sharpen the reticle to your eye without tools.

What the supplied information does not confirm

The supplied record does not include a specific mounting torque value, ring height recommendation, or a step-by-step procedure for setting the zero reset function beyond noting that it exists. It also does not confirm battery life for the illuminated reticle. For those details, consult the manufacturer's documentation or a qualified gunsmith. The catalog lists a 25-year international warranty (except US and Canada), a 2-year extended warranty, and an 80% electronics component warranty, but the supplied information does not detail what each warranty covers.

Related Articles

Customer Service
Home
Products
Cart
Profile